||Text of BMP
||A well must be a minimum distance of 150 feet from a surface property line, except with a waiver.
||"a. Statewide setbacks. Subparagraph (1) below shall apply to all areas of the state except as provided under subparagraphs b. and e. of this rule. ...
||Adequate blowout prevention equipment must be used on all well servicing operations.
||"(5) A. BOPE for well servicing operations. Adequate blowout prevention equipment shall be used on all well servicing operations. B. Backup stabbing ...
||All leasehold roads must accommodate local emergency vehicle access requirements.
||"(14) Access roads. If a wellsite falls within a high density area at the time of construction, all leasehold roads shall be constructed to ...
||All pipe fittings and well control equipment must have a working pressure rating.
||"i....Well control equipment and other safety requirements are:(4) All pipe fittings, valves and unions placed on or connected with blowout ...
||All stacks, vents, or openings must have screens to prevent wildlife entry.
||"b. Fired Vessel, Heater-Treater. (7) All stacks, vents, or other openings shall be equipped with screens or other appropriate equipment to prevent ...
||At installation, fired vessels and heater treaters must be 200 feet from occupied buildings.
||"b. Fired Vessel, Heater-Treater. (5) At the time of installation, fired vessels and heater treaters shall be a minimum of two hundred (200) feet ...
||At installation, tanks must be a minimum of 200 feet from any occupied buildings.
||"a. Crude Oil and Condensate Tanks. (3) At the time of installation, tanks shall be a minimum of two hundred (200) feet from any building unit."
||At time of construction, pits must be located at least 200 feet from any building unit.
||"f. Produced water pits, special use and buried or partially buried vessels, or structures. At the time of initial construction, pits shall be ...
||Blowout prevention equipment includes: Rig with Kelly.
||"(4) A. Blowout preventer equipment ("BOPE" ) for high density area drilling operations. Blowout prevention equipment for drilling operations shall ...
||Blowout prevention equipment includes: Rig without Kelly.
||"(4)... Blowout prevention equipment for drilling operations shall consist of (at a minimum): ii. Rig without Kelly. Double ram with blind ram and ...
||Blowout prevention equipment must be inspected daily.
||"i.... Well control equipment and other safety requirements are: (3) While in service, blowout prevention equipment shall be inspected daily and a ...
||Blowout prevention equipment must contain pipe rams that enable closure on the pipe being used.
||"i.... Well control equipment and other safety requirements are:(5) Blowout prevention equipment shall contain pipe rams that enable closure on the ...
||Blowout prevention is required by Rule 317 to be in accordance with API RP: 53.
||"i.... Well control equipment and other safety requirements are: (2) Blowout prevention equipment when required by Rule 317 shall be in accordance ...
||BOPE testing for high density area drilling operations.
||"B. BOPE testing for high density area drilling operations. Upon initial rig-up and at least once every thirty (30) days during drilling operations ...
||Closed chamber drill stem tests are allowed in high density areas.
||"D. Drill stem tests. Closed chamber drill stem tests shall be allowed in high density areas. All other drill stem tests shall require approval by ...
||Construct berms to contain and provide secondary containment
||"(12) Berm construction. Berms or other secondary containment devices in high density areas shall be constructed around crude oil, condensate, and ...
||Control of fire hazards.
||"(8) Control of fire hazards. Any material not in use that might constitute a fire hazard shall be removed a minimum of twenty-five (25) feet from ...
||Development from existing well pads.
||"(17) Development from existing well pads. Where possible, operators shall provide for the development of multiple reservoirs by drilling on existing ...
||Drilling contractors must place a sign at point of intersection between public and rig roads.
||"i.... Well control equipment and other safety requirements are: (9) Drilling contractors shall place a sign or marker at the point of intersection ...
||Each employee must have his job outlined and explained.
||"a. Employees shall be familiarized with these rules and regulations as provided herein as they relate to their function in their respective jobs. ...